Send a drawing
Home›Resources›Cases

Cases from our records

How drawings, samples, processes and inspections actually went. Each case comes from our own records; customer names and part numbers are left out.

Machining

Hinge pins that turn without noise

A German hinge maker needed precision hinge pins. We made them from 45 carbon steel, drawn twice and centreless ground to a surface roughness of Ra 0.3 µm or better, so the hinge turns without noise, play or binding in assembly.

Doors · case E-002

Hex Socket Shoulder Pins Black Oxide Knurled Rod Pins

A pin sized to an aluminium profile

A customer in New Zealand makes aluminium profile systems. Their connecting pin needed an outside diameter held to ±0.05 mm to fit the profile hole without play. We looked at knurling to control the diameter, recommended CNC turning for this tolerance, and sent a drawing for approval before production.

Construction · case E-069

Custom Knurling Pin Rivets Hex Socket Shoulder Pins

A beryllium copper pin, sourced in three days

A customer in Eastern Europe needed pins in UNS C17200 and had been looking for a supplier for a long time. We found a material source with mill certificates within three days, confirmed the drawing the next day and shipped samples with an inspection report. The production order followed without a further sample round.

case E-084

Custom CNC Machining Stainless Steel Fasteners

Inspection

Testing the samples a customer already had

A customer needed grade 10.9 parts with a salt spray requirement. We explained what drives the cost of that combination and offered to test samples from their other suppliers. Neither met the specification. The customer visited our plant and placed an order within a week.

case E-136

Die-mold

Holding a profile by measuring all the way round

On the same glass-door hinge rivet, we held the profile to the customer's requirement by measuring it through 360° during production, reworked the die for a cleaner head and edge, and compared wire from several suppliers to choose the most consistent batch.

Doors · case E-137

Stepped Eccentric Pins (Eccentric Step Rivets)

From a trade-show stand to ten years of parts

A maker of automotive lamp screws saw our die-mold parts at a trade show in Shanghai and contacted us. We have worked together for more than ten years and developed more than ten parts for them.

Automotive · case E-158

Ball Studs

Clean ends on a long-running square pin

A square pin formed from square wire has run with us for years. We redesigned the die for one end and added new equipment for the other, so both ends come out clean. Rejects at 100% inspection fell clearly, and the lower scrap made room for a lower price.

Doors · case E-138

One optical sort instead of two

On plastic-coated cam lock dowels, we added a dedicated vibratory feeder and transfer bridge at the die-mold stage to stop defective parts from earlier steps reaching later ones. With the process stable, the optical sorts after plating and after coating were merged into one final sort. Defects fell, packing labour per container dropped, and the coating machine is now on its third, fully automatic generation.

Furniture · case E-139

Cam Lock Dowels

Eccentric pins for a semi-automatic assembly line

A Polish maker of window and door hinges needed M8 eccentric step pins that feed through a semi-automatic assembly line. To get the hex socket and the 90° eccentric angle right for that line, we paused production, measured with the customer's own reference sample and method, and changed how the die locates the part. Both improved sample batches passed, and a production order for one million pieces followed.

Windows · case E-172

Eccentric Shoulder Screws Stepped Eccentric Pins (Eccentric Step Rivets) Solid Eccentric Pins (Eccentric Solid Rivets)

Cold heading

Ball studs for automotive lamps

A Korean maker of automotive lamps uses our ball studs in its lamp assemblies. Their drawings call the part a ball head stud; it is the same part.

Automotive · case E-004

Ball Studs Ball Studs With Hex Collar

T-bolts for vehicle roof racks

An Australian maker of vehicle accessories asked for black T-bolts in several lengths, grade 8.8 and 10.9. We compared cold heading with CNC for them and showed that the tooling charge was the actual cost of the die. Then we asked where the bolts would go: outdoor roof racks, where the previous supplier's bolts had rusted. We quoted black zinc-nickel instead. It was accepted, and caps and flanges were added to the order later.

Automotive · case E-049

Hammer Head T Bolts Long T Head Bolts

Cut or form

Four rods re-priced by changing the process

A pipe-fitting customer sent four drawings at 100,000 pieces each. Our first price was for turning. When they came back with a target price, we re-quoted all four as cold-headed parts. They wanted to pay for one die only, so that part was sampled cold-headed and the other three were turned. All four went into development once the samples were approved.

case E-047

Custom Threaded Rod

Samples in time for a trade show

A customer needed samples before a trade show. Cold heading would have meant waiting for a die, so we machined a small batch first, sent a drawing for confirmation and started straight away.

case E-071

Turned samples while the die is being made

A Korean furniture customer had a show to make, and cold-headed samples take about 30 days. We turned samples in 9 days and started the cold-heading die at the same time. For their later requests (a flange, a radius, a matte finish, the thread condition) we first worked out which options were feasible and what each would do to lead time, then let them choose.

Furniture · case E-183

Drawing review

A tyre stud drawing made producible

A trading customer had measured a sample and drawn a tyre stud with many tolerances tighter than the part needed. We marked up each one from production experience; they redrew it the next day and ordered samples. Their hole size was larger than usual, so we also sent studs with the common hole size to compare before they decided.

Automotive · case E-083

Removable Anti-Skid Tyre Studs for ATV, SUV, Motorcycle and Bicycle Tires

Repeat orders every year since 2023

For the same hinge maker we developed a new eccentric step screw. Drawing, tolerances and assembly feedback went back and forth over several rounds until they confirmed the part was in tolerance and assembled well. They have reordered every year from 2023 to 2026.

Windows · case E-173

Eccentric Shoulder Screws High Precision Eccentric Screws

Insert nuts for solid-wood beds

A Turkish bed maker asked for insert nuts. We asked where they go first: solid-wood bed frames, so we recommended steel. In their local test steel held poorly, and zinc alloy split at the washer. The pre-drilled hole turned out to be 9.5–10 mm, where we normally work with 11 mm, and zinc alloy is softer than steel. We recommended steel with a 10 mm hole; their own test found steel with a 9.7 mm hole worked best.

Furniture · case E-182

Zinc Alloy Insert Nuts Hanger Bolt And Insert Nut

Samples

Samples first, even when the customer offered to skip them

A furniture-connector trader in Taiwan added four new parts: a T-nut, a special nut, a stepped self-tapping screw and a custom screw. Based on earlier deliveries they offered to pay for tooling and go straight to production. We still made samples and had them test-fitted first.

Furniture · case E-157

T Nuts Custom Non Standard Nuts

Send a drawing

It reaches the person who quotes, not a shared inbox.

Each option opens an email with the questions we need answered already written in. Attach your file and send.

No mail app on this device? Write to zoe@tfscrew.com. What happens after you send it